Q10 PRO FIRMWARE. 1.0.7-FUTEKO-EN. HMD-1.0.7 2016-08-10.190824

[trykkertor]

Good spot.

The video needs re-encoding at a standard frame rate.



No Futeko, that video is made with smartphone to capturing the tv to show the problem. It's not the real video. This is details of real video that is a .mkv bluray rip:

Codec ID: V_MPEG4/ISO/AVC
Risoluzione: 720 x 404
Frame aspect ratio: 180:101 = 1.782178 (~16:9)
Pixel aspect ratio: 1:1 = 1
Display aspect ratio: 180:101 = 1.782178 (~16:9)
Framerate: 25 fps

With Kodi and MX Player Pro there's no judder.

Then you misunderstood him.
He wants you to give him a clip not working itself.
So he can download it, and experience the studder on his system.

[andys]

@andys:
Maybe it's just as simple as enabling samba again in settings.
I had to do it after the fw update since all previous settings were gone.
Works fine as before.

with samba works , does not work the USB 3.0 slave..this has never worked

[futeko.com]

No Futeko, that video is made with smartphone to capturing the tv to show the problem. It's not the real video. This is details of real video that is a .mkv bluray rip:

Codec ID: V_MPEG4/ISO/AVC
Risoluzione: 720 x 404
Frame aspect ratio: 180:101 = 1.782178 (~16:9)
Pixel aspect ratio: 1:1 = 1
Display aspect ratio: 180:101 = 1.782178 (~16:9)
Framerate: 25 fps

With Kodi and MX Player Pro there's no judder.

I would like a sample file to test. There should be no problem with that video. With 24p turned on it should output at 50Hz, so if you TV supports 50Hz it should be perfect.

Do you have the same problem with sample 4, section 4 here?: http://kodi.wiki/view/Samples

https://drive.google.com/file/d/0BwxFVkl63-lEWDUzUVUtZEw4cDA/view?usp=sharing

[Nice Monkey]

Does not work the USB 3.0 slave..this has never worked

Tried USB-Slave Mode on  a laptop running W10 Enterprise 64-bit.
Recognized immediately both on an USB-2 port and an USB-3 port. Using USB-3 reached a whopping 180 MByte/sec throughput using the Internal 8 TB HDD. This is also exactly the maximum specified for this HDD.

As I needed to move the player physically for the test, it had only power and USB-Slave connected and absolutely nothing else.
Maybe you could try that first.

[andys]

Does not work the USB 3.0 slave..this has never worked

Tried USB-Slave Mode on  a laptop running W10 Enterprise 64-bit.
Recognized immediately both on an USB-2 port and an USB-3 port. Using USB-3 reached a whopping 180 MByte/sec throughput using the Internal 8 TB HDD.

As I needed to move the player physically for the test, it had only power and USB-Slave connected and absolutely nothing else.
Maybe you could try that first.

:-\I do not go on w7 ultimate 64bit,just goes on usb 2.0

[Nice Monkey]

[ :-\I do not go on w7 ultimate 64bit,just goes on usb 2.0

Must be something with windows USB drivers, the port or cable.  Please try it with a different PC and try different (short) cables.
Will try my tower PC running W10 Home 32-bit also, but it is not a Windows thing. For Windows it is just another USB connected HDD.
My Dell Laptop e.g. was not supporting USB3 when installed with W7, had to download suitable USB3 drivers manually myself.
Be sure USB-3 is working correctly. When connected to an USB2 port on an USB3 capable PC  Windows should issue a warning "this device can work faster if connected to a USB3 port".  If this does not appear the setup is incorrect.

The USB3 Slave mode is a 100% Hardware feature implemented via the USB3-to-ATA bridge chip on the motherboard. The Q10 Pro does absolutely nothing for it. So FW revisions or even the OS itself don't matter in any way at all.

[andys]

[ :-\I do not go on w7 ultimate 64bit,just goes on usb 2.0

Must be something with windows USB drivers, the port or cable.  Please try it with a different PC and try different (short) cables.
Will try my tower PC running W10 Home 32-bit also, but it is not a Windows thing. For Windows it is just another USB connected HDD.
My Dell Laptop e.g. was not supporting USB3 when installed with W7, had to download suitable USB3 drivers manually myself.
Be sure USB-3 is working correctly. When connected to USB2 port the Windows PC should issue a warning "this device can work faster if connected to a USB3 port".

The USB3 Slave mode is a 100% Hardware feature implemented via the USB3-to-ATA bridge chip on the motherboard. The Q10 Pro does absolutely nothing for it. So FW revisions or even the OS itself don't matter in any way at all.

of Italian forum many have this problem , I think it is a motherboard problem, usb driver last update..with other device works
I installed extra w10 but the problem is the same!!

[Nice Monkey]

[of Italian forum many have this problem , I think it is a motherboard problem, usb driver last update..with other device works
I installed extra w10 but the problem is the same!!

Try a different PC. This excludes the very small chance there is something wrong with the USB-3 Slave port physically (badly soldered pin etc).
You then know for sure if it is your motherboard.

Nothing beats filling the Internal HDD via USB-3 Slave. You can even use your media player as a Docking Station when needing to update a HDD for any reason.    

[andys]

[of Italian forum many have this problem , I think it is a motherboard problem, usb driver last update..with other device works
I installed extra w10 but the problem is the same!!

Try a different PC. This excludes the very small chance there is something wrong with the USB-3 Slave port physically (badly soldered pin etc).
You then know for sure if it is your motherboard.

Nothing beats filling the Internal HDD via USB-3 Slave. You can even use your media player as a Docking Station when needing to update a HDD for any reason.   

my son mac pro , another son w8.. nothing ..what I want to try , this is problem is HIMEDIA firmware

[Nice Monkey]

[my son mac pro , another son w8.. nothing ..what I want to try , this is problem is HIMEDIA firmware

There is no FW active for this at all. Repeat it is done by a dedicate chip entirely. That is the reason why it can be so much faster that the Himedia processor/motherboard can handle.  If it is faulty and it looks like that then it is HW and you will need to ask for an RMA for it. If you got the box from Futeko then I am quite confident they will swap it for you.

[andys]

[my son mac pro , another son w8.. nothing ..what I want to try , this is problem is HIMEDIA firmware

There is no FW active for this at all. Repeat it is done by a dedicate chip entirely. That is the reason why it can be so much faster that the Himedia processor/motherboard can handle.  If it is faulty and it looks like that then it is HW and you will need to ask for an RMA for it. If you got the box from Futeko then I am quite confident they will swap it for you.

this is a fw problem, simply increase or decrease the power,I think , I'm not an expert

[aleister]

Hi
I new in this Forum, Hello togehter:)

With my Q10Pro im on FW  1.07 : HMD-1.0.7 2016-08-10.190824

Auto Framerate switching works fine so far. Before 1.07 i used the autofmt patch.

I had hopes 1.07 will solve a Problem with 720p/1080 50Hz PAL Sources.
The Auto FPS Change doesnt Switch 50hz! Only 25fps works , 24/23.976, 29.97 no Problems at all

It works with autofmt 1.0.11.1 , with Patch the Framerate goes on 50hz as it should

Samples for 50hz are on this Site:
Here on http://kodi.wiki/view/

For Examle on this 1080 50hz (and all my Movies on HDD) my Q10pro doesnt change the FPS
https://drive.google.com/file/d/0BwxFVkl63-lEbVptTVZ2NENURHM/view?usp=sharing

Greetings

[Nice Monkey]

Hi
I new in this Forum, Hello togehter:)

With my Q10Pro im on FW  1.07 : HMD-1.0.7 2016-08-10.190824

Auto Framerate switching works fine so far. Before 1.07 i used the autofmt patch.

I had hopes 1.07 will solve a Problem with 720p/1080 50Hz PAL Sources.
The Auto FPS Change doesnt Switch 50hz! Only 25fps works , 24/23.976, 29.97 no Problems at all

It works with autofmt 1.0.11.1 , with Patch the Framerate goes on 50hz as it should

Samples for 50hz are on this Site:
Here on http://kodi.wiki/view/

For Examle on this 1080 50hz (and all my Movies on HDD) my Q10pro doesnt change the FPS
https://drive.google.com/file/d/0BwxFVkl63-lEbVptTVZ2NENURHM/view?usp=sharing

Greetings

I can confirm PAL is changed to 25hz and NTSC to 30 hz not 50Hz and 60 Hz. Of course we talk interlaced source material at 50/60 Hz.
Will try the patch again and see what it does.

[aleister]

Its on Interlaced AND progressive Material...no FPS Auto Change to 50/60hz

With autofmt it works

Also autofmt changes 25fps Source to 50hz and 29,97 to 60hz,
Without Patch ist 25 to 25 and 29,97 to 29,97, Plays Ok but  autofmt fps should be optimal:)

[trykkertor]

I downloaded the 1.0.7 firmware from the link provide 1 or 2 pages earlier.
Today on my "Update" "Over the Air" it had a newer firmware than the one released 2-3 days ago.
The one i had ended with......24, and the new one OTA ended with......25.
Are there any differences between these two firms?